Follow this guide to remove a damaged tub to pump hose and install a new one so your washer can drain properly again. Water pooling under your washer often points to a worn or cracked hose. The tub to pump hose carries water from the outer tub to the drain pump during each cycle. When it weakens or splits, leaks can form quickly. Replacing it early helps prevent damage to your floor and keeps your washer working as it should.
Why the Tub to Pump Hose Fails
The hose is made of rubber and handles constant water flow, pressure, and movement. Over time, it can break down and start leaking.
- Normal wear and tear that causes cracking or dry rot
- Mineral buildup from hard water that stiffens the hose
- Improper installation that bends or stresses the hose
- Impact damage from objects hitting the washer base
Common Signs of a Failing Hose
Spotting early symptoms helps prevent bigger issues around your washer.
- Water pooling under or around the washer
- Damp flooring after each wash cycle
- Visible cracks or splits along the hose surface
- Dripping water during draining cycles
- Musty smells from trapped moisture
- Reduced draining performance
- Water marks or stains near the base of the washer
- Sudden increase in water usage
- Loose or slipping hose connections
- Noise from water leaking or spraying inside
What You Need
Gather everything before starting the repair.
- Replacement tub to pump hose W10802689 compatible with your model
- Pliers
- Wooden block
Safety Precautions
Take a few minutes to prepare your workspace and reduce risks.
- Unplug the washer or switch off the breaker before starting
- Turn off the water supply at the wall outlet
- Allow the washer to cool if it was recently used
- Place towels nearby to catch leftover water
- Work in a clean, well-lit area
- Keep children and pets away from the workspace
- Keep hands dry when working around internal parts
- Handle components carefully to avoid damage
- Wear gloves to protect your hands from sharp edges
- Avoid touching exposed wires or terminals
- Take photos of connections before removing parts
How to Replace Tub-To-Pump Hose in Whirlpool, Kitchenaid, and Maytag Washer
Follow these steps to remove the old hose and install a new tub-to-pump hose safely and correctly.
Preparation and Setup
- Unplug the washer from the power outlet
- Turn off the water supply line
- Move the washer away from the wall to create enough working space
- Place a towel under the front edge of the washer to catch any water
Access the Bottom of the Washer
- Place a sturdy wooden block in front of the washer
- Carefully tilt the washer forward and rest it securely against the block
- Remove the installation pad at the bottom by bending the edges upward and pulling it out
Remove the Old Tub-to-Pump Hose
- Locate the tub-to-pump hose at the bottom of the washer
- Use pliers to squeeze the tabs on the upper hose clamp
- Slide the clamp up the hose away from the connection point
- Pull the hose off the outlet port and wiggle it gently if it feels stuck
- Remove both hose clamps from the old hose
Install the New Tub-to-Pump Hose
- Slide the upper and lower clamps onto the new hose
- Push the new hose onto the outlet port until it sits firmly in place
- Move the clamps back over the connection points
- Adjust the clamps so they hold the hose tightly
Reassemble and Test the Washer
- Reinstall the bottom installation pad by bending it back into position
- Carefully return the washer to the upright position
- Plug the washer back in
- Turn the water supply back on
- Slide the washer back into place without pinching hoses or cords
- Run a test cycle and check for any leaks around the hose connections
To Recap
Fixing a leaking tub to pump hose is a smart way to protect your washer and the space around it. A small crack or loose connection can quickly turn into a bigger problem if left alone. Taking the time to swap out the hose keeps water flowing the right way and helps your machine run through each cycle without trouble.
Pay attention to early signs like puddles, slow draining, or visible wear on the hose. Catching these issues early makes the repair much simpler and helps avoid damage to your floor or nearby parts. With the right tools and a careful approach, this is a repair most homeowners can handle with confidence.
Once the new hose is in place and everything is secured, your washer should drain properly again. A quick test run gives you peace of mind and lets you confirm that the leak is gone and the system is working as it should.