Bosch Gas Range Igniter Mounting Clip Replacement

An igniter that shifts out of position can make a gas burner unreliable. A small mounting clip holds the igniter at its designed location beneath the cooktop. Bosch gas range igniter mounting clip replacement requires careful access to the burner bases and cooktop, followed by a check that the igniter tip is secure. Part 00189322 should be verified against the full range model before purchase.

The source procedure removes the grates and four burner bases, reaches the clip from beneath the cooktop, and reassembles the range. It also contains a tip suggesting a torch for stuck hardware. That tip is unsafe around a gas appliance and is excluded here; stuck fasteners should be handled by a qualified technician.

Signs the Clip May Be the Problem

These observations can lead to an igniter-position check:

• The igniter tip moves when lightly inspected with power off.
• A burner sparks but does not light reliably.
• The clip looks cracked or is missing.
• The igniter sits at a different height from the model’s intended position.
• A burner base cannot align correctly around the igniter.
• Clicking continues after the burner has been checked for basic cap alignment.

Ignition trouble can also involve a dirty burner, damaged igniter, or electrical fault. The clip should be replaced when its fit is actually defective, not simply because a burner hesitates to light.

Safety Before Cooktop Work

• Turn off range power at the breaker or unplug it, as the installation allows.
• Close the gas supply before moving or opening cooktop parts where the model requires it.
• Let burners and grates cool completely.
• Do not apply open flame or a torch to seized hardware on a gas range.
• Keep the igniter tip from being bent or struck.
• Support the cooktop so wiring is not pulled tight.
• Stop if a gas line, fitting, or electrical connector is damaged.
• Seek qualified service if access differs from the model instructions.

The source lists a flathead screwdriver, 13/16-inch socket wrench, towel, gloves, and replacement clip. The exact fastener size and layout should be checked on the actual model.

How to Replace the Igniter Mounting Clip

Set removed parts aside in order. An igniter and burner base must return to their original alignment for the final test to mean anything.

Remove the Grates and Burner Bases

1. Disconnect range power by unplugging it or turning off its circuit breaker.
2. Lift the grates straight up and put them in a safe place.
3. Remove the burner caps without bending them.
4. Use the source’s 13/16-inch socket wrench to loosen the nuts that hold the burner bases.
5. Lift off the four burner bases and keep them with their matching parts.

If a nut is seized, stop rather than heating it. The source’s torch suggestion must not be followed. A technician can choose a safe method that fits the appliance and local gas-work rules.

Access and Remove the Old Clip

6. Place a towel at the back of the range to protect the finish.
7. Pull the cooktop forward gently, leaving enough slack in the wiring and connectors, and rest it on the towel.
8. Locate the rectangular igniter clip on the underside of the cooktop.
9. Put a flathead screwdriver into the clip’s slot and pry gently toward the installer until it releases from the bracket and igniter plug.
10. Remove the old clip and check that no fragment remains in the mounting area.

A broken fragment can keep the new clip from seating. Use a flashlight if the area is hard to see, and avoid pressing the screwdriver against the igniter tip.

Install the New Clip

11. Orient the new clip with its slit side facing outward.
12. Push the igniter plug from behind while sliding the clip into place over it.
13. Guide the clip onto its bracket with the flathead screwdriver if needed.
14. Check that it sits flush in the retaining notch.
15. Tug it gently to confirm that it is locked. Remove and reseat it if it remains loose.

The source cautions against bending the delicate igniter tip. A clip that needs heavy force may be the wrong part or may be misaligned. Verify the part and bracket rather than pushing harder.

Reassemble and Test

16. Lower each of the four burner bases back into position, aligning the notch around its igniter tip.
17. Reinstall the mounting nuts with the socket wrench. Tighten them securely without overtightening.
18. Fit the burner caps onto the bases.
19. Return the grates to their original places without scraping the cooktop.
20. Restore electrical power after the cooktop and burner parts are secure.
21. Test each burner separately for normal sparking, prompt ignition, and steady flame.
22. Shut the burner off if ignition or flame behavior is abnormal, then recheck the component alignment with power off.

Never leave a burner releasing gas while investigating weak ignition. If a gas odor appears, stop testing and follow gas-emergency guidance from outside the area.

What to Check After the Repair

The final result should be visible as well as audible:

• The new clip remains flush in its bracket.
• The igniter tip stays in its intended position.
• Burner bases fit around their igniters without contact.
• Caps and grates sit flat.
• Every burner lights promptly during a brief test.
• No gas odor or unusual flame appears.

If ignition remains unreliable, the clip may not have been the only problem. A dirty burner opening, damaged igniter, or control fault needs its own diagnosis.

Record which burner still has the issue. A problem limited to one position may help a technician focus on that burner and its igniter. If several burners behave abnormally after the cooktop was moved, stop using the range and have the reassembly checked.

In Summary

Bosch gas range igniter mounting clip replacement depends on gentle access and correct part alignment. Remove burner components in order, protect the cooktop and wiring, then seat the new clip without bending the igniter. A secure tip and normal ignition across the burners provide the practical final check.