Quick answer
The Whirlpool dishwasher door spring WPW10337934 needs replacing when the door falls open on its own, will not stay half open, or a stretched or snapped spring is visible at the door-side hinge mechanism. The spring costs $25 to $35 and takes 20 to 45 minutes to swap with a screwdriver, nut driver, and pliers. Inspect both springs and replace worn pairs for even door tension.
The door drops as soon as your hand leaves the handle. Replacing the Whirlpool dishwasher door spring WPW10337934 may restore support, but only if the spring is the failed part. A broken link or cable can produce the same heavy-door complaint.
What should you check before ordering? The model number and door panel matter because this spring supports a particular load. The wrong tension can leave a door too heavy or make it pull shut.
Start with the symptom checks below, then confirm fit and gather the tools. The replacement sequence also explains how to inspect the related supports and judge whether another part needs repair.
Quick Facts
Use these details to plan the work:
- Difficulty: Easy to moderate
- Time: 20 to 45 minutes
- Tools: Phillips screwdriver, suitable nut driver, needle-nose pliers, gloves, flashlight, towels, and wrench needed for any water connection
- Part cost: $25 to $35 per spring
- Skill level: Care required around the loaded spring
Order the part with confidence
- Guaranteed to fit when you search by model number
- Same-day shipping on in-stock parts
- 365-day returns on any part
- Free tech support before and after you buy
What Symptoms Mean the Whirlpool Dishwasher Door Spring Has Failed?
A failed spring can let the door fall open, feel unusually heavy, or lose its normal balance. A visible break or stretched coil supports a spring diagnosis, while a loose connection may point to another part.
Use these symptoms to narrow the problem.
| Symptom | Possible Cause | What Helps Separate It |
|---|---|---|
| Door falls open | Spring, link, or cable failure | Visible damage in the balance system |
| Door will not hold partway open | Uneven or incorrect tension | Correct spring and mounting position |
| One side feels heavy | One side’s support has failed | Compare both spring connections |
| Coil stretched or snapped | Spring failure | Direct evidence at the coil |
| Door catches or rubs | Hinge damage or alignment | Movement is uneven rather than simply heavy |
Keep a hand on the door while opening it. A broken balance system means the door may fall faster than expected. Do not use repeated drops as a way to confirm the symptom.
Is WPW10337934 the Right Door Spring for Your Whirlpool Dishwasher?
The Whirlpool dishwasher door spring WPW10337934 must match both the model and the door load. A spring that looks close can still have the wrong tension.
Confirm these details before buying.
- Full model number from the door-area label
- Original door panel type and any added panel weight
- Listed replacement or superseded part numbers
- Correct part listing under a KitchenAid or Kenmore badge, if applicable
Do not match a spring by color alone unless the model’s parts information specifically uses that color to identify it. The part number and full model lookup are stronger checks. An older spring may also look different from a valid replacement without making that replacement wrong.
Which Whirlpool Dishwasher Models Use Door Spring WPW10337934?
Whirlpool WDF510PAYS6 is a documented replacement example for WPW10337934. Confirm every other full model and door configuration.
- WDF510PAYS6 uses this service spring
- WPW10337934 replaces W10337934, W10462694, 8268989, and 8524473
Not every machine within a family uses the same door weight or spring system. Include the model’s final digits and letters, and confirm the installed door panel before choosing a pair.
What Tools Do You Need to Replace the WPW10337934 Door Spring?
Have the tools ready before releasing a loaded spring or moving the dishwasher.
- Phillips screwdriver
- Suitable nut driver
- Needle-nose pliers
- Work gloves
- Flashlight
- Towels or floor protection
- Container for residual water
- Wrench for water fittings, if they must be disconnected
Gloves protect against some sharp edges, but the spring can still move suddenly. Support the door and control the spring’s movement. Stop if access is too tight to unhook it without losing your grip.
How to Replace the Door Spring on a Whirlpool Dishwasher Step by Step
Follow these steps with power and water off, using the shown side-hinge spring-and-bushing layout only when it matches your model.
Phase 1: Cut Power and Access the Door-Side Spring
- Disconnect power, shut off water, and adjust the legs to clear the cabinet opening.
- Remove the mounting screws, usually at the top front.
- Pull the appliance straight out without catching hoses or wiring; disconnect any connections that cannot move safely.
- Protect the floor and move the appliance only far enough for spring access.
Phase 2: Remove the Old Spring and Retain the Bushing
- Locate the spring at the side of the door mechanism.
- Note its original mounting notch.
- Unhook the spring under control, retaining the plastic bushing.
- Remove the bushing from the old spring.
- Inspect the mounting area for damage.
Phase 3: Install the New Spring and Check Door Balance
- Transfer the intact bushing to the new spring.
- Hook the spring into the original notch.
- Stretch it carefully and place the bushing on the hinge pin.
- Release tension slowly and check secure seating.
- Test door movement; use the model’s approved tension positions if adjustment is needed.
- Slide the dishwasher back without pinching connections.
- Reconnect and clamp the drain hose if detached.
- Reconnect the water line if detached.
- Adjust the leveling legs.
- Refit the cabinet mounting screws.
- Restore the water supply.
- Keep the breaker off while checking that electrical covers and connections are secure.
- Reconnect an unplugged cord only with its breaker off, then restore the breaker after all electrical covers are secure.
- Run a test and check leaks and door movement.
- Shut off water and recheck connections if a leak appears.
Didn't fix it? Ask a technician on the AppliancePartsPros forum.
Post your model number, the symptom, and what you've already tried. Appliance techs and experienced DIYers answer for free, usually the same day.
Ask the forum →80,000+ solved repair threads · no account needed to readShould You Replace One Spring or Both?
A pair can help when both original springs have similar wear. It does not replace the need to inspect links, cables, and hinges that may be causing the imbalance.
Compare the whole support system before choosing parts.
- Pair of correct springs: Budget two current per-spring prices when both coils are worn; do not assume a pair is under $40.
- One confirmed failed spring: Consider the condition and tension of the remaining side.
- Worn spring link: Replace the damaged connection as well; a new coil cannot hold through a cracked link.
- Hinge damage: Repair the hinge fault before relying on spring adjustment.
The Whirlpool dishwasher door spring WPW10337934 should support the correct door, not force a damaged door into alignment. Does the door still rub after the spring swap? That result needs a separate hinge or installation check.
FAQ
How Long Does It Take to Replace a Whirlpool Dishwasher Door Spring?
Allow about 20 to 45 minutes for access, replacement, and door checks. A difficult cabinet opening or other damage can make the work longer.
Why Does the Door Still Drop After a New Spring?
The other spring, a broken link, a cable, or the mounting position may still be wrong. Confirm the replacement fits the door’s weight before changing tension.
Can the Wrong Spring Make the Door Too Stiff?
Yes, a spring with too much force can make the door difficult to open or cause it to pull shut. Use the full model and door type to choose the correct part.
Bringing the Dishwasher Door Back Into Balance
The Whirlpool dishwasher door spring WPW10337934 should help the correct door move with even support and latch smoothly. A correct spring and sound connections make that balance possible.
Find the door spring WPW10337934 matched to your full model number and door type so both sides can balance evenly.
Still stuck after this guide?
Two free options: post your model number and symptom on the forum, or search the model number in the shop to see every part that fits.
