Refrigerators depend on a thermistor to maintain a stable internal climate. When this part fails, temperature swings can lead to spoiled food and higher energy use. Replacing a faulty thermistor restores proper cooling and keeps your appliance performing well.
This guide explains the function of the WPW10384183 thermistor, common signs of failure, and the tools needed for replacement.
What the Thermistor Does
The thermistor measures the temperature in the fresh food compartment and sends this information to the control board. The control board uses this data to adjust compressor run times and maintain the target temperature.
When the thermistor stops working, the control board cannot regulate cooling accurately. This can cause food to freeze, warm unexpectedly, or spoil more quickly.
Signs of a Faulty Thermistor
Watch for these symptoms:
- Refrigerator or freezer is too warm or too cold
- Temperature in the refrigerator changes without reason
- Refrigerator runs continuously without cycling off
- Error code on the control panel related to temperature
- Cooling cycle does not start even when the interior is warm
How to Confirm the Thermistor Is the Problem
Before buying a replacement, you can test the thermistor to be sure it is faulty:
- Check for error codes on your refrigerator’s display panel that relate to temperature sensors
- Use a multimeter to measure the resistance of the thermistor at room temperature and compare it to the manufacturer’s specifications
- Place the thermistor in a cup of ice water and test again to see if the resistance changes as expected
- Inspect the wiring for signs of fraying, burn marks, or corrosion
- Verify that other components, such as the control board or compressor, are functioning normally
Tools and Materials Needed
Gather the following before you begin:
- Flathead screwdriver
- Wire cutters
- Wire strippers
- Utility knife
- Pliers or crimping tool
- Heat gun
- Heat shrink tubing
- Butt connectors
- Replacement thermistor compatible with your model
Why Replacement Matters
Allowing a bad thermistor to remain in place can waste electricity and put extra strain on the compressor. Replacing it promptly helps maintain consistent cooling and can prevent costly repairs later.
How to Replace the Thermistor in Your Refrigerator
Here are the steps to safely remove the old thermistor and install a new one in your Whirlpool, KitchenAid, or Maytag refrigerator.
Access the Thermistor
- Turn off the refrigerator and unplug it from the power outlet.
- Locate the cover plate on the left side of the fresh food compartment ceiling near the control panel.
- Open the refrigerator door and use a small flathead screwdriver to gently pry the plate off.
- Find the thermistor sensor behind the opening.
- If the thermistor has a plug connector, detach it. If it is hardwired, continue to the next step.
Remove the Old Thermistor
- Use a utility knife to carefully cut away the insulation from the wires connected to the old thermistor.
- Use wire cutters to snip the wire, leaving at least ½ inch protruding from the wall or compartment side.
- Remove the old thermistor.
- Use a utility knife to strip approximately ¼ inch of insulation from the ends of the cut wires.
Prepare the New Thermistor
- Strip ¼ inch of insulation from each wire end on the new thermistor using wire strippers.
- Slide a butt connector onto each exposed copper wire end of the new thermistor.
- Use pliers or a crimping tool to firmly crimp each connector.
- Perform a gentle pull test to confirm the wires are secure.
- Cut small sections of heat shrink tubing and slide one over each butt connector.
- Use a heat gun to shrink the tubing until it seals the joint, applying heat slowly from a distance.
Install the New Thermistor
- Insert the new thermistor into the plastic 4-prong housing inside the refrigerator compartment.
- Rotate the base clockwise until it locks into place.
- Replace the cover plate.
- Close the refrigerator door and plug the appliance back in.
- Allow time for the refrigerator to return to the proper temperature.
- Use an independent thermometer to confirm the temperature is correct.
Also Read: Thermistor Failure in Frigidaire Refrigerator: Signs and Solution
To Recap
A fresh thermistor can make the difference between a fridge that struggles and one that keeps food fresh without wasting energy. Knowing the signs of failure and tackling the replacement early protects your groceries and avoids bigger repair bills. The WPW10384183 model is designed to restore accurate temperature readings so the control board can do its job. With the right tools and careful steps, this fix is straightforward and brings your refrigerator back to reliable cooling.