If your Kenmore dryer is making noise or isn’t spinning properly, the belt tension roller could be the culprit. Here’s a straightforward, step-by-step guide to help you test and replace it—no need for a repair call!
How to Identify a Faulty Belt Tension Roller
Before diving into a repair, it’s helpful to know if the belt tension roller is indeed the issue. Here are some signs that indicate the tension roller may need replacement:
- Squeaking or Squealing Noises: If you hear a high-pitched squeak or squeal while the dryer is running, it’s often a sign that the belt tension roller is worn out. The noise is caused by friction between the roller and the belt, especially if the roller bearings are damaged.
- Thumping or Rattling Sounds: A worn-out or misaligned tension roller may produce a thumping or rattling noise. This can happen if the roller no longer spins smoothly, causing uneven movement as the drum turns.
- Drum Not Spinning: If the dryer drum isn’t turning but you can hear the motor running, a faulty tension roller could be causing the belt to slip. The roller provides tension to keep the belt tight; without it, the belt may lose grip and prevent the drum from spinning.
- Visible Wear or Damage: Inspect the roller for visible signs of wear, like cracks, dents, or grooves. If the roller looks damaged or feels loose when you touch it, it’s likely time to replace it.
If your Kenmore dryer displays any of these symptoms, the belt tension roller may be the source of the problem. Identifying these signs early can help prevent further damage to your appliance and make the repair process quicker and more efficient.
Tools You’ll Need
- 1/4-inch nut driver
- Putty knife
- #20 Torx bit
- Small flat-head screwdriver
Safety Precautions
Safety is essential when working with any appliance. Follow these tips to ensure a safe and smooth repair:
- Power Off and Unplug: Always turn off and unplug your appliance before starting any maintenance. If your dryer is hardwired, switch off the circuit breaker. This prevents electrical shock.
- Allow Time to Cool: If the dryer was recently in use, give it enough time to cool down.
- Take Your Time: Avoid rushing through the repair to prevent accidents and ensure precision.
- Ensure Good Lighting: Work in a well-lit area so you can easily see and access all parts.
- Declutter the Workspace: A tidy workspace reduces hazards. Keep children and pets away for their safety.
- Dry Hands and Area: Never work on an appliance with wet hands or in a damp area to avoid electrical shock.
- Consult the User Manual: Check your user manual for specific installation or safety guidelines related to your model.
- Be Gentle with Parts: Handle components carefully to avoid damage and personal injury.
- Wear Insulated Gloves: These will protect your hands from sharp edges and debris.
- Exercise Caution with Wires: Avoid touching exposed wires or terminals. If you must, use non-conductive tools or insulating gloves.
- Document Connections: Take photos or make notes of wiring and terminal connections before you disconnect them, making reassembly much easier.
How to Test and Replace the Belt Tension Roller on a Kenmore Electric Dryer
Step 1: Access the Belt Tension Roller
- Use a putty knife to press in on the two clips at the corners of the console.
- Push the console up and back.
- Remove the three ¼-inch screws securing the top of the dryer.
- Slide the top towards the front of the dryer and remove it.
- Disconnect the door switch.
- Press in on the two clips holding the front panel with the putty knife.
- Remove the two door springs.
- Open the door and take out the lint screen.
- Use a ¼-inch nut driver to remove the three screws holding the blower housing.
- Detach the blower housing from the dryer.
- Locate the yellow wire attached to the bottom of the front panel and disconnect it.
- Remove the two ¼-inch screws at the bottom of the front panel.
- Use a Torx 20-bit to remove the two screws at the top of the front bulkhead.
- Lift off the front panel.
- Reach under the drum and release the belt from the idler pulley.
- Use the drum belt to lift the drum out of the cabinet.
Step 2: Test the Belt Tension Roller
- Find the idler or tension roller.
- Turn the roller by hand to check for stiffness or grooves.
- If the roller is hard to turn or has grooves, it needs replacement.
- Do not apply any lubricant to the roller.
Step 3: Remove the Old Belt Tension Roller
- Use a small screwdriver to remove the triangular keeper holding the roller in place.
- Slide the roller off the shaft.
Step 4: Install the New Belt Tension Roller
- Clean the shaft with a paper towel.
- Place the new roller on the shaft.
- Secure the roller with the triangular keeper.
Step 5: Reassemble the Dryer
- Reinstall the drum in the cabinet.
- Reattach the belt to the idler pulley.
- Reattach the front bulkhead using the two Torx screws at the top.
- Secure the bulkhead with the two ¼-inch screws at the bottom.
- Reinstall the blower housing with the three screws.
- Reconnect the yellow sensor wire.
- Reinstall the two door springs.
- Attach the door switch.
- Reinstall the top cover and snap it into place.
- Open the door and insert the lint screen.
- Plug the dryer back in or turn on the breaker to restore power.
Also read: Why Cleaning Your Dryer Vents is Crucial for Faster Drying Times
Conclusion
And there you have it! With this guide, you’re all set to tackle a common dryer issue and get your Kenmore running smoothly again. Not only does replacing the belt tension roller help your dryer work more efficiently, but it also saves you the cost and wait time of a repair call.
Just remember to keep safety first, and take it one step at a time. You’ll be surprised at how straightforward it can be! Here’s to more quiet, hassle-free laundry days!