How to Replace Whirlpool Dishwasher Door Strike WP8574157 Fast

Push the door closed and it springs back without catching. A damaged Whirlpool dishwasher door strike WP8574157 can prevent a sound latch from holding, though hinge, gasket, and latch faults can cause similar trouble. Repeated slamming may add wear without fixing the cause.

Which side of the catch is damaged? Inspect the strike and latch before deciding what to replace.

The checks below explain the strike’s location, model fit, and signs of wear. The retaining-tab replacement sequence then shows how the new part seats and how to check engagement without forcing the door.

Quick Facts

Use these details to plan the work:

• Difficulty: Easy
• Time: 10 to 15 minutes
• Tools: Flathead screwdriver, flashlight
• Part cost: Check the current model-specific quote
• Skill level: Beginner

What Symptoms Mean the Whirlpool Dishwasher Door Strike Needs Replacing?

A cracked or worn strike may let the latch hook slip away instead of holding the door. A door that pops open can also have a latch, hinge, or seal problem, so the symptom alone does not identify the failed part.

Use the door’s behavior to narrow the cause.

Is WP8574157 the Right Door Strike for My Whirlpool Dishwasher?

Whirlpool dishwasher door strike WP8574157 is the catch mounted near the top of the tub opening. The latch mechanism is inside the door and engages that catch when you close it.

Confirm these details before ordering.

• The complete model number from the door-edge label
• The tub-mounted strike location and retaining design
• The current part listing for that exact model
• The older 8574157 number, where cross-referenced to WP8574157

Which Whirlpool Dishwasher Models Use Door Strike WP8574157?

A confirmed example is KitchenAid KUDS01FLSS6. A brand or short family name does not establish fit.

• Match the full appliance number.
• Look up the tub-mounted strike.
• Confirm WP8574157 or its listed substitute.
• Compare its retaining tabs and brackets.

What Tools Do I Need to Replace the WP8574157 Door Strike?

The retaining-tab strike uses a flathead screwdriver to release its tabs. Keep the screwdrivers that match your machine available, but do not remove unrelated screws to free this clip-retained part.

Gather these items for the work.

• Flathead screwdriver
• Phillips or Torx T20 screwdriver, if required by your model
• Flashlight
• Protective gloves
• Safety glasses

Disconnect power before the repair and keep your hands and work area dry. Let the machine cool after a hot cycle. The plastic housing and metal tabs need gentle handling, since extra force can create another broken part.

How to Replace Whirlpool Dishwasher Door Strike WP8574157 Step by Step

Follow these steps to replace the retaining-tab strike and check engagement.

Phase 1: Cut Power and Open the Door Fully

1. Disconnect power before starting.
2. Open the dishwasher door.
3. Locate the rectangular strike near the top opening on either side, as fitted.

Phase 2: Release the Retaining Tabs and Remove the Old Strike

1. Locate the metal retaining tabs at both ends.
2. Press the left tab down with a flathead screwdriver while pulling that end forward.
3. Release the right tab the same way without cracking the plastic.
4. Remove the released strike.

Phase 3: Seat the New Strike in Its Brackets

1. Line up the replacement strike.
2. Slide one end into its bracket until it clicks.
3. Flex the outer tab inward and slide in the opposite end.
4. Check for firm retention at both tabs.
5. Center the strike gently without over-bending the tabs.
6. Seat its base nearly flush with the bracket.

Phase 4: Check Strike Retention and Latch Alignment

1. Keep power off while checking the door.
2. Open and latch it several times without force.
3. Check both retaining ends if the hook misses.
4. Restore power after reassembly and check a normal start.

This design is held by tabs rather than two strike screws. A firmly seated strike should stay centered and catch the hook without heavy pressure. A door that still refuses to catch needs a separate latch assessment.

Should You Replace the Strike, the Latch, or Both?

Compare current model-specific quotes after the damaged component is confirmed. The genuine strike catalog lists about $58 at the time of checking; prices can change.

• Strike: Suitable for a cracked or worn catch surface.
• Latch assembly: Suitable when the latch hook fails to spring back or the assembly is damaged.
• Both: Consider both when prolonged slamming has damaged the catch and the latch.

Whirlpool dishwasher door strike WP8574157 is a small repair when the rest of the door is sound. It will not straighten a damaged hinge or remove a seal obstruction. The goal is normal engagement, not a door that closes only with force.

FAQ

How Long Does It Take to Replace a Whirlpool Dishwasher Door Strike?

Allow about 10 to 15 minutes for an accessible strike. A separate latch or alignment fault can take longer to diagnose and repair.

Can I Bend the Old Strike Back Instead?

Do not rely on bending to repair cracked or worn plastic. A small position correction is different from trying to restore material that has broken away.

Why Does the Door Still Pop Open After a New Strike?

The latch may be worn, the strike may not be centered, or the hinges or gasket may keep the door out of line. A new catch cannot correct every cause of poor closure.

A Door That Catches on the First Push

A good strike meets a sound latch with light, steady pressure. Confirm the location and retaining design before choosing Whirlpool dishwasher door strike WP8574157, then use the door check to confirm that the catch holds.

Confirmed the door strike is cracked or worn where the latch hook catches? Look up WP8574157 against your Whirlpool model number and order the replacement so the door latches on the first push.