Quick answer
Frigidaire dishwasher heating element 154825001 replaces a heater that leaves dishes wet and cold, stalls the heated wash, or shows a visible break, and it fits many Frigidaire, Frigidaire Gallery, and Electrolux models, so confirm fit by model number. Test the old element first: a healthy element reads roughly 10 to 30 ohms, and OL means it is open. Replacement takes 45 to 90 minutes and costs $35 to $80.
Cold plates and wet dishes can make a working wash cycle feel unfinished. The Frigidaire dishwasher heating element 154825001 is one possible cause, but a safety thermostat or control fault can leave the same result. Drying trouble alone is not proof that the heater has failed.
How can you tell whether a new element will help? A model check and meter test give you better grounds for the decision than the symptoms alone.
The checks below cover heater testing and part fit before moving to replacement. Pay particular attention to the mounting nuts and wire connections beneath the tub.
Quick Facts
Use these details to plan the work:
- Difficulty: Moderate
- Time: 45 to 90 minutes
- Tools: Multimeter, Phillips and Torx T20 screwdrivers, nut driver, adjustable wrench, towels, flashlight
- Part cost: $35 to $80
- Skill level: Intermediate
What Are the Symptoms of a Failed Dishwasher Heating Element?
A failed element can leave dishes cold and wet or prevent a heated wash from finishing normally. A visible break or blister strengthens the case, while other symptoms still need a test.
Compare what you see with the parts that may be involved.
| Symptom | What It Can Point To |
|---|---|
| Wet, cold dishes | Element, hi-limit thermostat, or control |
| Little heat at the end | Heater circuit not working |
| Long or stalled heated wash | Element or heater control |
| Blister or break on the metal loop | Damaged element |
| Heater-related code | A heater circuit fault requiring tests |
The hi-limit thermostat is a safety switch that opens at excessive heat. The separate thermistor senses temperature.
How Do I Test the Heating Element With a Multimeter for Continuity?
Follow these steps to test the disconnected element before ordering a replacement.
Check the Element With Power Off
- Turn off the dishwasher breaker and confirm the terminals are not live.
- Remove the kick plate to reach the element connections beneath the tub.
- Disconnect both element terminals.
- Set the multimeter to ohms and measure across the element terminals.
- Compare the reading with the expected range of roughly 10 to 30 ohms.
- Treat an OL reading as an open circuit that calls for a replacement element.
- Check each terminal against the metal sheath for an unwanted connection to ground.
Ohms measure electrical resistance. OL means the meter cannot find a complete path through the element. Do not check resistance with the dishwasher powered.
Is 154825001 the Right Heater for My Frigidaire Dishwasher?
Confirm compatibility using the complete model number and mounting design.
Use these details when checking the part.
- Full model number from the door-edge tag
- Terminal spacing
- Mounting nuts and attachment points
- Element shape and retaining clips
- Separate hi-limit thermostat listing
Frigidaire dishwasher heating element 154825001 is a specific part, rather than a universal heater.
Which Frigidaire Dishwasher Models Use Heating Element 154825001?
This heater appears in selected Frigidaire, Frigidaire Gallery, and Electrolux families. A family name can narrow the lookup, but it cannot confirm every model in that group.
The relevant families include these series.
- Frigidaire FFBD
- Frigidaire FGBD
- Frigidaire FGHD
- Frigidaire Gallery
- Electrolux EI
Match the complete model number with the parts diagram, including its ending characters.
Should I Cut Power Before Replacing the Heating Element?
Yes, cut power before touching the element or its wires. This heater uses 120 volts, so the dishwasher’s control button is not a safe substitute for disconnecting power.
Prepare the work area before the replacement.
- Switch off the breaker or unplug the dishwasher.
- Confirm the terminals are dead with a voltage tester.
- Let the element cool after a recent cycle.
- Close the water supply before pulling the unit forward.
- Keep towels ready for water left in the lines.
A technician can handle electrical checks and installation if you are uncomfortable reaching the wiring.
How to Install Frigidaire Dishwasher Heating Element 154825001 Step by Step
Follow these steps to replace the confirmed failed element on a matching dishwasher.
Phase 1: Cut Power and Access the Element Terminals Under the Tub
- Open the door with power and water disconnected.
- Remove the lower rack.
- Pull the lower spray arm straight up.
- Remove both countertop screws with a Phillips screwdriver.
- Slide the dishwasher halfway out to reach the terminals.
Phase 2: Remove the Lower Rack and Lift Out the Old Element
- Disconnect the element wires and note their positions.
- Remove both mounting nuts with a 1/2-inch wrench.
- Withdraw the terminals through the tub and release the retaining clips.
- Compare the old and new elements for a match.
Phase 3: Seat the New Element and Tighten the Mounting Nuts
- Insert the new terminals through the tub, aligning both white locator dots with the clips.
- Start the nuts by hand, then tighten them with the wrench.
Phase 4: Reconnect the Terminals, Restore Power, and Run a Heated Cycle
- Reconnect the wires with their plastic insulators fitted; either wire can use either terminal.
- Slide the dishwasher back.
- Refit both countertop screws.
- Press the spray arm onto its hub and check free rotation.
- Reinstall the rack.
- Close the door.
- Restore water and power.
- Run a test cycle to confirm operation.
Should You Replace the Element, the Hi-Limit Thermostat, or the Control?
Replace the part that fails its test. A heater reading within range should lead to further checks, rather than an automatic element order.
These costs help you compare the choices.
- Element: About $35 to $80 when it reads open, with roughly an hour for the work.
- Hi-limit thermostat: About $15 to $35 when the element is good but the safety switch has failed.
- Control board: About $120 to $250 only after the element and thermostat pass.
Burnt terminal connectors need professional attention. A new Frigidaire dishwasher heating element 154825001 cannot correct a damaged connection by itself. The cause of the damaged wiring needs attention as well.
FAQ
Does a Failed Element Stop the Wash Cycle?
It can cause a heated wash to run long, stall, or show a heater-related fault. Some cycles may continue, but that does not mean the dishwasher has heated the water correctly.
Why Are the Dishes Still Wet After a New Element?
A separate thermostat or control problem may still be present. A replacement heater also cannot fix a connection that was left loose or damaged during the repair.
How Long Does a Dishwasher Heating Element Last?
There is no single lifespan that fits every dishwasher and water supply. A resistance test and the element’s condition give you better grounds for replacement than age alone.
Hot Water and Dry Dishes Again
Your meter result and model number are the two useful checks before this purchase. A confirmed open heater gives you a clear reason to replace the element and restore normal heat.
Find the replacement heating element for your dishwasher after confirming that 154825001 matches your full model number, so the next cycle can heat and dry properly.
